- #Slicer for fusion 360 says material is too small zip file
- #Slicer for fusion 360 says material is too small full
You home the machine which is several millimeters above the screen. In summary, the vat is removed and a piece of paper is laid on the screen. It was an easy process that I followed in the included manual. The first thing you do before printing is level the build plate to the screen. It was uneventful and the directions were clear and concise. I immediately updated the firmware following instructions found on their website. After replacing the board the Anycubic Photon S could read the USB drive. It was not difficult to replace the board. I notified Anycubic and they sent me a replacement. I wasn’t planning on tearing down this printer but after powering on the first time the printer would not read any USB drive. Printing material: 405nm photosensitive resinĪnycubic Photon S Unboxing & Teardown Click to Enlarge Click to Enlarge Click to Enlarge Click to Enlarge Only Issue.Light-source: UV integrated light(wavelength 405nm).Printing Technology: LCD-based SLA 3D Printer.Quite a few people are successful but with the price of these inexpensive printers, I am not sure DIY is the way to go. The frame was built with 20 aluminum extrusion.
![slicer for fusion 360 says material is too small slicer for fusion 360 says material is too small](https://d2n4wb9orp1vta.cloudfront.net/cms/brand/MMS/2020-MMS/1120-mms-native-autodesk-f360-interface.png)
Along with a ramps board for the electronics. In hindsight, I believe my leveling process was flawed. I attempted to build one about a year ago and failed. This is not my very first foray with SLA printing.
#Slicer for fusion 360 says material is too small full
One thing to note is that the print height dictates how long the print will take not how full the build plate is. This repeats until the print is complete. The plate raises, lowers slightly less than the previous layer and hardens that layer. The LCD screen turns on the pixels it wants to expose to the ultraviolet light which hardens the resin in those areas. When a print is started the build plate lowers all the way down to the bottom of the vat filled with resin. The vat is filled with resin that hardens when exposed to ultraviolet light. Above that is a vat with a bottom made of FEP. The LEDs turn on and shine through a 2k LCD screen. At the bottom of this printer is a bunch of ultraviolet 405nm LEDs. LCD based SLA printers work a little differently. Most everyone is familiar with this kind of 3D printing and is easy to understand. The filament is fed to a hot end which melts the plastic and deposits layers. FDM printers use plastic filament on a roll.
![slicer for fusion 360 says material is too small slicer for fusion 360 says material is too small](https://3dprinting.com/wp-content/uploads/2019/02/Fusion-19-copy.jpg)
You might ask what is that? If you are a long-time reader you may have ran across my traditional FDM printer reviews. In this first post, I will be sharing my initial experiences with the Anycubic Photon S. I will be breaking this one down into at least 2 posts. and the part numbers are being obscured by the outlines on the small pieces and the sequence is being scattered such that i have to look at all of the files to find the next one.Ī more crude way i found that may work is to use slic3r witch is part of the repetier package i can using applescript automate advancing 1 slice and snapping a screen shot and repeat but i have honeycomb grid and other infill structures around obscuring some of the small details near the edges like the nostrils holes on the nose and ears and eyes gaps.Hey, Karl here with something different. The only downside i can see immediately is that some of the parts are small in the assembly viewer that it will not highlight the small pieces.
#Slicer for fusion 360 says material is too small zip file
That is like segmenting a 100 meg zip file into 10 segments of 10 meg then segmenting each segment into 10 segments of 1 meg. I found a way around that limitation by saving bigger slices say 1 inch thick then then making 1 millimeter slices of each big slice. Most slicers make 1000 to 2000 slices but slicer for fusion limits to 100 maybe as high as 150.
![slicer for fusion 360 says material is too small slicer for fusion 360 says material is too small](https://core-electronics.com.au/media/wysiwyg/tutorials/Stephen/LaserCutting/Slicer/Slicer-menu-screenshot-Fusion360.png)
Thanks it works however it is very limited in resolution. I am ok with spending time assembling inkjet printed slices and gluing them together. The best priced 3d printers are a couple hundred even as kit and using a 3d printing house like shapeways complains about exceeding the bounding box and is too slow as if i change something i have to wait for it to re render the changes and calculate the prices. Ink is cheap too i have refillable cartridges and ink is available in bulk for ciss and refillable cartridges. Paper is cheap a ream of 500 sheets is $10 to $15 at local office store I am looking to do 3d models in paper by stacking.Īnd was wondering if there are any programs that will save the outline of the slices as an image file so i can print them on paper and cut out with exacto knife. I saw a post at " where the slices are saved as images but above method requires snapping shots of the screen witch includes the grid and everything else on screen